Viewing file: 
serial.h (4.56 KB) -rw-r--r--Select action/file-type:
(
+) |
(
+) |
(
+) |
Code (
+) |
Session (
+) |
(
+) |
SDB (
+) |
(
+) |
(
+) |
(
+) |
(
+) |
(
+) |
/* ASB2303-specific 8250 serial ports
*
* Copyright (C) 2007 Red Hat, Inc. All Rights Reserved.
* Written by David Howells (dhowells@redhat.com)
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public Licence
* as published by the Free Software Foundation; either version
* 2 of the Licence, or (at your option) any later version.
*/
#ifndef _ASM_UNIT_SERIAL_H
#define _ASM_UNIT_SERIAL_H
#include <asm/cpu-regs.h>
#include <proc/irq.h>
#include <linux/serial_reg.h>
#define SERIAL_PORT0_BASE_ADDRESS 0xA6FB0000
#define SERIAL_PORT1_BASE_ADDRESS 0xA6FC0000
#define SERIAL_IRQ XIRQ0 /* Dual serial (PC16552) (Hi) */
/*
* The ASB2303 has an 18.432 MHz clock the UART
*/
#define BASE_BAUD (18432000 / 16)
/*
* dispose of the /dev/ttyS0 and /dev/ttyS1 serial ports
*/
#ifndef CONFIG_GDBSTUB_ON_TTYSx
#define SERIAL_PORT_DFNS \
{ \
.baud_base = BASE_BAUD, \
.irq = SERIAL_IRQ, \
.flags = STD_COM_FLAGS, \
.iomem_base = (u8 *) SERIAL_PORT0_BASE_ADDRESS, \
.iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM, \
}, \
{ \
.baud_base = BASE_BAUD, \
.irq = SERIAL_IRQ, \
.flags = STD_COM_FLAGS, \
.iomem_base = (u8 *) SERIAL_PORT1_BASE_ADDRESS, \
.iomem_reg_shift = 2, \
.io_type = SERIAL_IO_MEM, \
},
#ifndef __ASSEMBLY__
static inline void __debug_to_serial(const char *p, int n)
{
}
#endif /* !__ASSEMBLY__ */
#else /* CONFIG_GDBSTUB_ON_TTYSx */
#define SERIAL_PORT_DFNS /* both stolen by gdb-stub because they share an IRQ */
#if defined(CONFIG_GDBSTUB_ON_TTYS0)
#define GDBPORT_SERIAL_RX __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_RX * 4, u8)
#define GDBPORT_SERIAL_TX __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_TX * 4, u8)
#define GDBPORT_SERIAL_DLL __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_DLL * 4, u8)
#define GDBPORT_SERIAL_DLM __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_DLM * 4, u8)
#define GDBPORT_SERIAL_IER __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IER * 4, u8)
#define GDBPORT_SERIAL_IIR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_IIR * 4, u8)
#define GDBPORT_SERIAL_FCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_FCR * 4, u8)
#define GDBPORT_SERIAL_LCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_LCR * 4, u8)
#define GDBPORT_SERIAL_MCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_MCR * 4, u8)
#define GDBPORT_SERIAL_LSR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_LSR * 4, u8)
#define GDBPORT_SERIAL_MSR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_MSR * 4, u8)
#define GDBPORT_SERIAL_SCR __SYSREG(SERIAL_PORT0_BASE_ADDRESS + UART_SCR * 4, u8)
#define GDBPORT_SERIAL_IRQ SERIAL_IRQ
#elif defined(CONFIG_GDBSTUB_ON_TTYS1)
#define GDBPORT_SERIAL_RX __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_RX * 4, u8)
#define GDBPORT_SERIAL_TX __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_TX * 4, u8)
#define GDBPORT_SERIAL_DLL __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_DLL * 4, u8)
#define GDBPORT_SERIAL_DLM __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_DLM * 4, u8)
#define GDBPORT_SERIAL_IER __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_IER * 4, u8)
#define GDBPORT_SERIAL_IIR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_IIR * 4, u8)
#define GDBPORT_SERIAL_FCR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_FCR * 4, u8)
#define GDBPORT_SERIAL_LCR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_LCR * 4, u8)
#define GDBPORT_SERIAL_MCR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_MCR * 4, u8)
#define GDBPORT_SERIAL_LSR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_LSR * 4, u8)
#define GDBPORT_SERIAL_MSR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_MSR * 4, u8)
#define GDBPORT_SERIAL_SCR __SYSREG(SERIAL_PORT1_BASE_ADDRESS + UART_SCR * 4, u8)
#define GDBPORT_SERIAL_IRQ SERIAL_IRQ
#endif
#ifndef __ASSEMBLY__
#define LSR_WAIT_FOR(STATE) \
do { \
while (!(GDBPORT_SERIAL_LSR & UART_LSR_##STATE)) {} \
} while (0)
#define FLOWCTL_WAIT_FOR(LINE) \
do { \
while (!(GDBPORT_SERIAL_MSR & UART_MSR_##LINE)) {} \
} while (0)
#define FLOWCTL_CLEAR(LINE) \
do { \
GDBPORT_SERIAL_MCR &= ~UART_MCR_##LINE; \
} while (0)
#define FLOWCTL_SET(LINE) \
do { \
GDBPORT_SERIAL_MCR |= UART_MCR_##LINE; \
} while (0)
#define FLOWCTL_QUERY(LINE) ({ GDBPORT_SERIAL_MSR & UART_MSR_##LINE; })
static inline void __debug_to_serial(const char *p, int n)
{
char ch;
FLOWCTL_SET(DTR);
for (; n > 0; n--) {
LSR_WAIT_FOR(THRE);
FLOWCTL_WAIT_FOR(CTS);
ch = *p++;
if (ch == 0x0a) {
GDBPORT_SERIAL_TX = 0x0d;
LSR_WAIT_FOR(THRE);
FLOWCTL_WAIT_FOR(CTS);
}
GDBPORT_SERIAL_TX = ch;
}
FLOWCTL_CLEAR(DTR);
}
#endif /* !__ASSEMBLY__ */
#endif /* CONFIG_GDBSTUB_ON_TTYSx */
#endif /* _ASM_UNIT_SERIAL_H */
